Search

SCADA Articles on SCADA World

Wireless SCADA

2010-11-17 17:56:09views: 802Bentek Systems

Wireless SCADA

Wireless SCADA is required in those applications when wireline communications to the remote site is prohibitively expensive or it is too time consuming to construct wireline communications. In particular types of industry like Oil & Gas or Water & Wastewater, wireless SCADA is often the only solution due to the remoteness of the sites. Wireless SCADA systems can be built on private radio (licensed or unlicensed), cellular or satellite communications; each of these has its unique set of characteristics.

 

Private Licensed (i.e. UHF) Private License-free (i.e. SS) Cellular (i.e. Telus, Nextel) Satellite (i.e.Tachyon, Satalarm)

Typ. Range (miles)

20 - 40

20

cell site coverage

North America

Government Approval

Yes

No

No

No

Setup Time

Moderate

Fast

Fast

Fast

Data Rate (kbps)

9600

9600 to 19,200

9600

1200 to 1.2M

Monthly Rates?

No

No

Yes

Yes

RTU / RF integration

Not usually

Yes

Yes

Yes



One major difference between Private Radio and Cellular or Satellite is that Private radio has no associated monthly fees. Once you build your hardware infrastructure, you own it. With Cellular or Satellite Service providers, there is an associated monthly fee. This is usually $30 or greater per month depending on the Service Plan.

For the decision maker, it comes down to deciding between a large capital investment and no monthly service fees OR a smaller capital investment with monthly service fees. If the clients remote assets are well within the Service Providers coverage area, they have high speed or TCP/IP data requirements or their remote sites are there for a short term (lasting no more than 1 or 2 years) all of these factors contribute to making Cellular communications a more attractive option.

If the assets are extremely remote (hundreds or thousands of miles away from civilization) and /or they have TCP/IP LAN speed requirements then Satellite communications is obviously the only solution. Often it is more typical for companies to have a mixture of solutions; using Point-Multipoint Private Radio communications where there is a high density of remote sites served by the one Master site, using Cellular for sites for from Private radio clusters and or satellite for the very remote sites.

Another difference between Private Radio networks and Cellular or Satellite networks is expansion capabilities. With Private Radio systems, if distances between communicating sites are too great for a single hop, then repeaters can always be installed to further the range. This certainly adds to the overall project cost but it is at least an option if required.

With Cellular or Satellite, one is leveraging the vast existing infrastructure of the Service Provider. The advantage of Cellular or Satellite is that the client has access to very wide coverage but the disadvantage is that if there is a site that happens to be outside of the Service Providers coverage, there is no way for the client to increase the range; only the Service Provider can do that.

If Cellular communications makes sense as the overall SCADA strategy, it is possible to use Private Radio as "Last Mile Links" to these few remote sites that fall outside of the Cellular coverage maps.... to extend the coverage from the Cellular to a Private network to get to these remote assets.

The typical wireless SCADA architecture is Point-Multipoint with one Master polling multiple remote RTU’s (Remote Terminal Units) or PLC's using RTU or PLC data communication protocols including protocols such as Modbus, AB-DF1, and DNP3.0.

Each PLC or RTU at the remote site is programmed with a unique system address and those addresses are all configured into the SCADA Host MMI. The SCADA Host then polls these addresses and stores the acquired data into its database. It will perform centralized alarm management, data trending, operator display and control.

Modern SCADA Host MMI's like NetSCADA can easily accommodate many different types of industrial protocols and the architecture allows multiple clients to view the same data and seamless expansion to handle additional remote sites and i/o points.

Bentek Systems provides complete turnkey SCADA and Wireless SCADA communications solutions from the SCADA Host MMI to the Satellite or Cellular communications or Private Radio communications.

Wireless SCADA systems can range from simple Point-Multipoint systems like the 900-MB Spread Spectrum system below using Modbus protocol.

Link: http://www.scadalink.com/support/technotesCell.html

SCADA Articles

Using Free Tools To Detect Attacks On SCADA Networks
2015-05-09 14:28:25views: 1740

ICS/SCADA experts say open-source network security monitoring software is a simple and cheap way to catch hackers targeting plant operations. Operators at Natanz nuclear facility in Iran might well have caught Stuxnet before it spread and sabotaged operations at the plant if they had been watching the wires for anomalous network traffic, a pair of ICS/SCADA experts say.

Hackers gain full control of critical SCADA systems
2015-05-09 14:04:07views: 1806

Russian researchers have found vulnerabilities in industrial control systems that they say grant full control of systems running energy, chemical and transportation systems. The vulnerabilities were discovered by researchers who over the last year probed popular and high-end ICS and SCADA systems used to control everything from home solar panel installations to critical national infrastructure.

SCADA Attacks Double in 2014
2015-05-06 07:17:15views: 1620

Annual threat report from Dell Security shows not only a significant surge in the number of attacks on retail credit card systems, but industrial SCADA systems as well, which are much more likely to go unreported.
For Dell to report an annual surge in point-of-sale (POS) attacks aimed at payment card infrastructures might not be such a surprise to people who pay any attention to the news.

The Industrial Software Revolution Begins Now
2013-10-16 11:33:59views: 2193

Invensys is kicking off the conference “The Industrial Software Revolution Begins Now” and underscoring the ‘revolution’ concept with the release of its Wonderware InTouch 2014 and Wonderware System Platform 2014 software.

Integrating Video into HMI/SCADA
2012-06-29 10:19:55views: 2492

The useful integration of video with industrial control systems has been a reality for a few years, but a burst of applications and installations is on the horizon. Cheaper bandwidth, wide availability of Internet protocol (IP) cameras, and greater familiarity with industrial Ethernet networks seem to be driving user interest.

AdvancedHMI - a different approach to HMI development
2012-06-14 10:46:48views: 1793

AdvancedHMI base package is a free software used to build HMIs that display information residing in a PLC. You will find it to be one of the fastest platforms to build an HMI with. The software takes advantage of the Visual Basic .NET development environment so effort is focused on the core software and not reinventing a development environment.

Web Services and SCADA
2012-06-12 23:06:33views: 1371

Web services can be another method for connectivity to SCADA and MES systems. They can retrieve tomorrow's weather, the price of stocks or commodities, the time of sunrise and sunset, and a slew of other publicly-available resources.

SCADA virtualisation with WinCC Version 7
2011-12-21 12:01:11views: 1311

As automation solutions become increasingly complex, it follows that the effort required to maintain both hardware and software will also increase. PCs must be provided with suitable specification and operating systems to support the applications.

Cloud-Based SCADA Systems: The Benefits and Risks
2011-12-20 22:57:31views: 928

Cloud computing is a hot topic. As people become increasingly reliant on accessing important information through the Internet, the idea of storing or displaying vital real-time data in the cloud has become more commonplace. With tech giants like Apple, Microsoft, and Google pushing forward the cloud computing concept, it seems to be more than just a passing trend.

An alternative to DCS or PLC/SCADA
2011-10-04 13:46:22views: 874

Traditionally, users have had a choice between a DCS or a PLC/SCADA approach when selecting a control system for use in process control applications. A key benefit of traditional DCSs was that the suppliers took a ‘systems approach’ and it was designed for large scale applications.